Performance prediction of trailing-edge cooling system of gas turbine blade using detached eddy simulation

Authors

  • Agus Jamaldi Department of Mechanical Engineering, Sekolah Tinggi Teknologi Warga Surakarta. 57552. Indonesia.
    Indonesia
  • Hassan Khamis Hassan Zanzibar Water Authority, P.O. Box 460, Zanzibar, Tanzania.
    Tanzania, United Republic of

DOI:

https://doi.org/10.23917/arstech.v1i1.15

Keywords:

Trailing-edge cooling , Detached eddy simulation, Discharge coefficient , Film cooling effectiveness, Staggered array

Abstract

This study evaluates the performance of the trailing-edge (TE) cooling system in a gas turbine blade. Eddy Simulation (DES), based on the turbulence model of Spallart-Almaras (SA), was used to simulate the TE cooling system. A TE configuration with a five-row staggered pin-fin arrangement was employed as a computational domain. Three parameters, i.e., the coefficient of heat transfer on the pin-fins surface (hpin), the coefficient of discharge (CD), and the effectiveness of adiabatic film cooling were used to assess the performances. The findings denoted that the heat transfer fluctuations occurred on the surface of the pin-fins in each row. The discharge coefficient increased with the rising of the blowing ratio. The trend predicted data of adiabatic film cooling effectiveness were in good agreement with realistic discrepancies compared to other researches, mainly for higher blowing ratio. The average effectiveness along the cut-off region was to be sensitive to the blowing ratio changes, which was attributed to the structures of turbulent flow along the mixing region.

Downloads

Download data is not yet available.

References

J. Han, 'Recent studies in turbine blade cooling', Rotating Machinery, vol. 10, no. 6, pp.443–457, 2004. https://doi.org/10.1080/10236210490503978

P. Martini, A. Schulz, C.F. Whitney, and E. Lutum, 'Experimental and numerical investigation of trailing edge film cooling downstream of a slot with internal rib arrays', Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy, vol. 217, pp.393–401,.2003. https://doi.org/10.1243/095765003322315450

B. Facchini, L. Innocenti, and L. Tarchi, 'Pedestal and end-wall contribution in heat transfer in thin wedge', Proceedings of ASME Turbo Expo No. GT-2004-53152, pp.101–111, 2004. https://doi.org/10.1115/GT2004-53152

Z. Yang and H. Hu, 'An experimental investigation on the trailing edge cooling of turbine blades', Propulsion and Power Research, vol. 1, no. 1, pp.36–47, 2012. https://doi.org/10.1016/j.jppr.2012.10.007

A.L. Brundage and M.W. Plesniak, 'Experimental investigation of airfoil trailing edge heat transfer and aerodynamic losses', Experimental Thermal and Fluid Science, vol. 31, no. 3, pp.249–260, 2007. https://doi.org/10.1016/j.expthermflusci.2006.04.004

M. Axtmann, R. Poser, J. von Wolfersdorf, and M. Bouchez, 'Endwall heat transfer and pressure loss measurements in staggered arrays of adiabatic pin–fins', Applied Thermal Engineering, vol. 103, pp.1048–1056, 2016..https://doi.org/10.1016/j.applthermaleng.2016.04.066

J. Joo and P. Durbin, 'Simulation of turbine blade trailing edge cooling', Journal of Fluids Engineering, vol. 131, no. 2, pp.021102, 2009. https://doi.org/10.1115/1.3054287

S.A. Lawson, A.A. Thrift, K.A. Thole, and A. Kohli, 'Heat transfer from multiple row arrays of low aspect ratio pin–fins', International Journal of Heat and Mass Transfer, vol. 54, no. 17–18, pp.4099–4109, 2011. https://doi.org/10.1016/j.ijheatmasstransfer.2011.04.001

N. Azwadi and E. Kianpour, 'The effect of blowing ratio on film cooling effectiveness using cylindrical and row trenched cooling holes with alignment angle of 90 degrees', Mathematical Problems in Engineering, pp. 1–9, 2014. https://doi.org/10.1155/2014/470576

J. Ahn, I.S. Jung, and J.S. Lee, 'Film cooling from two rows of holes with opposite orientation angles?: injectant behavior and adiabatic film cooling effectiveness', International Journal of Heat and Fluid Flow, vol. 24, no. 1, pp.91–99, 2003. https://doi.org/10.1016/S0142-727X(02)00200-X

J. Armstrong and D. Winstanley, 'A review of staggered array pin fin heat transfer for turbine cooling applications', Journal of Turbomachinery, vol. 110, pp. 94–103, 1988. https://doi.org/10.1115/1.3262173

M. Axtmann, J. von Wolfersdorf, and G. Meyer, 'Application of the transient heat transfer measurement technique in a low aspect ratio pin fin cooling channel', Journal of Turbomachinery, vol. 137, 2015, https://doi.org/10.1115/1.4031267

D.E. Metzger, R.A. Berry, and J.P. Bronson, 'Developing heat transfer in rectangular ducts with staggered arrays of short pin–fins', Journal of Heat Transfer, vol. 104, no. 4, pp.700–706, 1982. https://doi.org/10.1115/1.3245188

G. Delibra, D. Borello, K. Hanjalic, and F. Rispoli, 'URANS of flow and end-wall heat transfer in a pinned passage relevant to gas-turbine blade cooling', International Journal of Heat and Fluid Flow, vol. 30, pp.549–560,.2009. https://doi.org/10.1016/j.ijheatfluidflow.2009.03.015

M.K. Chyu, Y.C. Hsing, T.I.-P. Shih, and V. Natarajan, 'Heat transfer contributions of pins and end-wall in pin-fin arrays: Effects of thermal boundary condition modelling', Journal of Turbomachinery, vol. 121, no. 2, pp.257–263, 1999. https://doi.org/10.1115/1.2841309

M. Effendy, Y.F. Yao, and J. Yao, 'Effect of mesh topologies on wall heat transfer and pressure loss prediction of a blade coolant passage', Applied Mechanics and Materials, vol. 315, pp. 216–220, 2013. https://doi.org/10.4028/www.scientific.net/AMM.315.216

Y. Yao, M. Effendy, and J. Yao, 'Evaluation of wall heat transfer in blade trailing-edge cooling passage', Applied Mechanics and Materials, vol. 284, pp.738–742, 2013. https://doi.org/10.4028/www.scientific.net/AMM.284-287.738

M. Effendy, Y.F. Yao, and J. Yao, 'Comparison study of turbine blade with trailing-edge cutback coolant ejection designs', 51st AIAA Aerospace Sciences Meeting including the New Horizons Forum and Aerospace Exposition, 2013. https://doi.org/10.2514/6.2013-548

M. Effendy, Y.F. Yao, J. Yao, and D.R. Marchant, 'Predicting film cooling performance of trailing-edge cutback turbine blades by detached eddy simulation', 52nd Aerospace Sciences Meeting, 2014. https://doi.org/10.2514/6.2014-0279.

P. Martini, A. Schulz, and S. Wittig, 'Experimental and numerical investigation of trailing edge film cooling by circular coolant wall jets ejected from a slot with internal rib arrays', Turbomachinery, vol. 126, no. 2, pp.229-236,2004. https://doi.org/10.1115/1.1645531

P. Martini, A. Schulz, and H. Bauer, 'Film Cooling Effectiveness and Heat Transfer on the Trailing–edge Cutback of Gas Turbine Airfoils with Various Internal Cooling', Journal of Turbomachinery, vol. 128, pp.196–205, 2006, https://doi.org/10.1115/1.2103094

M. Effendy, Y.F. Yao, and J. Yao, 'Pressure loss and wall heat transfer characteristics in blade trailing-edge cooling passage', Proceedings of the International Symposium on Turbulence, Heat and Mass Transfer, 2012..https://doi.org/10.1615/ICHMT.2012.ProcSevIntSympTurbHeatTransfPal.560

T. Horbach, A. Schulz, and H.J. Bauer, 'Trailing edge film cooling of gas turbine airfoils – effects of ejection lip geometry on film cooling effectiveness and heat transfer', Heat Transfer Research, vol. 41, no. 8, 2010. https://doi.org/10.1115/1.4002964

D.S. Holloway and J.H. Leylek, 'Pressure-side bleed film cooling: part IE steady framework for experimental and computational results', Proceedings of ASME Turbo Expo 2002 No. GT-2002-30471, pp. 835–843, 2002.

F. Menter and Y. Egorov, 'The scale-adaptive simulation method for unsteady turbulent flow predictions. Part 1?: Theory and model description', Flow, Turbulence and Combustion, vol. 85, no. 1, pp. 113-138, 2010. https://doi.org/10.1007/s10494-010-9264-5

M. Effendy, Y.F. Yao, and D. R. Marchant, 'Detached-eddy simulation of trailing-edge (TE) cutback turbine blade cooling', MATEC Conferences No. 135, p.00008, 2017..https://doi.org/10.1051/matecconf/201713500008

H. Schneider, D. Von Terzi, and H. Bauer, 'Large-eddy simulations of trailing-edge cutback film cooling at low blowing ratio', International Journal of Heat and Fluid Flow, vol. 31, no. 5, pp. 767–775, 2010. https://doi.org/10.1016/j.ijheatfluidflow.2010.06.010

J. Krömer, W. Schröder, M. Meinke, P. Comte, C. Brun, and M. Haberkorn, ‘LES of transitional boundary layers and wakes with trailing edge blowing’, Numerical Flow Simulation III, vol 82. Springer, Berlin, Heidelberg, 2003. https://doi.org/10.1007/978-3-540-45693-3_15

M. Effendy, Y.F. Yao, and D.R. Marchant, 'DES study of blade trailing edge cutback cooling performance with various lip-thicknesses', Applied Thermal Engineering, vol. 99, pp. 434–445, 2016. https://doi.org/10.1016/j.applthermaleng.2015.11.103

Y. Gao, X. Yan, J. Li, and K. He, 'Investigations into film cooling and unsteady flow characteristics in a blade trailing–edge cutback region', Mechanical Science and Technology, vol. 32, no. 10, pp. 5015–5029, 2018. https://doi.org/10.1007/s12206-018-0949-3

M. Effendy, Y.F. Yao, J. Yao, and D.R. Marchant, 'Detached eddy simulation of blade trailing-edge cutback cooling performance at various ejection slot angles', International Journal of Heat and Fluid Flow, vol. 80, 2019, https://doi.org/10.1016/j.ijheatfluidflow.2019.108487

M. Effendy, Y.F. Yao, J. Yao, and D.R. Marchant, 'Pin-fin shape and orientation effects on wall heat transfer predictions of gas turbine blade', AIP Conference Proceedings, vol. 2114. 2019. https://doi.org/10.1063/1.5112392

M. Effendy, Y.F. Yao, D. Sugati, and T. Tjahjono, 'Numerical study of pin-fin cooling on gas turbine blades', AIP Conference Proceedings, vol. 2114. 2019. https://doi.org/10.1063/1.5112493

Downloads

Published

2020-06-05

How to Cite

Jamaldi, A., & Hassan, H. K. (2020). Performance prediction of trailing-edge cooling system of gas turbine blade using detached eddy simulation. Applied Research and Smart Technology (ARSTech), 1(1), 16–21. https://doi.org/10.23917/arstech.v1i1.15