Important for Readers

We invite readers to sign up for ARSTech journal's publishing notification service. Using the Register button for the journal at the top of the homepage. With each new issue of the journal, this registration will result in the reader receiving the Table of Contents via email. Often, this list helps the journal to assert some degree of support or readership. See the journal's Privacy Policy, which ensures readers will not use their name and email address for other purposes.

The authors of various reputable journals have cited published articles in the ARSTech journal, and they come from various regions of the world. Based on the Scopus indexed, some of the articles cited are as follows:

(1)  Prototype development of mecanum wheels mobile robot: A review; MA Abd Mutalib, NZ Azlan; Applied Research and Smart Technology (ARSTech) 1 (2), 71-82, 2020. -----> 9 Citations

  1. Szeremeta, Mateusz, and Marcin Szuster. "Neural tracking control of a four-wheeled mobile robot with mecanum wheels." Applied Sciences 12, no. 11 (2022): 5322; https://doi.org/10.3390/app12115322
  2. Dosoftei, Constantin-Catalin, Alexandru-Tudor Popovici, Petru-Razvan Sacaleanu, Paul-Marcelin Gherghel, and Cristina Budaciu. "Hardware in the loop topology for an omnidirectional mobile robot using matlab in a robot operating system environment." Symmetry 13, no. 6 (2021): 969; https://doi.org/10.3390/sym13060969
  3. Racz, Sever-Gabriel, Mihai Crenganiș, Radu-Eugen Breaz, Adrian Maroșan, Alexandru Bârsan, Claudia-Emilia Gîrjob, Cristina-Maria Biriș, and Melania Tera. "Mobile Robots—AHP-Based Actuation Solution Selection and Comparison between Mecanum Wheel Drive and Differential Drive with Regard to Dynamic Loads." Machines 10, no. 10 (2022): 886; https://doi.org/10.3390/machines10100886
  4. Apurin, Artem, Bulat Abbyasov, Liaisan Safarova, Alexandra Dobrokvashina, Tatyana Tsoy, Edgar A. Martínez-García, and Evgeni Magid. "LIRS-ArtBul: Design, Modelling and Construction of an Omnidirectional Chassis for a Modular Multipurpose Robotic Platform." In International Conference on Interactive Collaborative Robotics, pp. 70-80. Cham: Springer International Publishing, 2022. https://doi.org/10.1007/978-3-031-23609-9_7
  5. Leng, Jie, Haiming Mou, Jun Tang, Qingdu Li, and Jianwei Zhang. "Design, Modeling, and Control of a New Multi-Motion Mobile Robot Based on Spoked Mecanum Wheels." Biomimetics 8, no. 2 (2023): 183; https://doi.org/10.3390/biomimetics8020183
  6. Tolani, Manoj, Abiodun Afis Ajasa, Arun Balodi, Ambar Bajpai, Yazeed AlZaharani, and Sunny. "Advanced Sensor Systems for Robotics and Autonomous Vehicles." In Artificial Intelligence for Robotics and Autonomous Systems Applications, pp. 439-459. Cham: Springer International Publishing, 2023. https://doi.org/10.1007/978-3-031-28715-2_14
  7. Torres-Martínez, A. A., E. A. Martínez-García, R. Lavrenov, and E. Magid. "Four Wheeled Humanoid Second-Order Cascade Control of Holonomic Trajectories." In Artificial Intelligence for Robotics and Autonomous Systems Applications, pp. 461-486. Cham: Springer International Publishing, 2023. https://doi.org/10.1007/978-3-031-28715-2_15
  8. Abd Mutalib, Mohd Azri, and Norsinnira Zainul Azlan. "Development of Lab Scale MAVeP Mobility Prototype." International Journal of Automotive and Mechanical Engineering 19, no. 3 (2022): 9971-9981; https://doi.org/10.15282/ijame.19.3.2022.09.0769
  9. Brown, Noah, Trey Pierce, Gloria Ma, James McCusker, and Filip Cuckov. "Development of Kinematic and Dynamic Model of an Omnidirectional Four Mecanum Wheeled Robot." In ASME International Mechanical Engineering Congress and Exposition, vol. 86670, p. V005T07A031. American Society of Mechanical Engineers, 2022; https://doi.org/10.1115/IMECE2022-96143

(2)  The effectivity of used-oil as quenching medium of 42-CrMo4 steel for automotive materials; H Hariningsih, S Sumpena, H Sukarjo; Applied Research and Smart Technology (ARSTech) 1 (1), 28-34 -----> 3 Citations

  1. Hariningsih, Hariningsih, and Tri Widodo Besar Riyadi. "Effect of hardening and tempering on the microstructure and mechanical properties of the tapered-forged leaf spring steel." In Materials Science Forum, vol. 1029, pp. 25-32. Trans Tech Publications Ltd, 2021. https://doi.org/10.4028/www.scientific.net/MSF.1029.25
  2. Mohammed Mossaab, Blaoui, Abdelwahab Zerrouki, Mourad Nouioua, Hassan Guendouz, Hammoudi Abderazek, and Ali Bouchoucha. "A new quenching method to improve the mechanical properties of metals." Advances in Materials and Processing Technologies 8, no. 4 (2022): 4471-4482. https://doi.org/10.1080/2374068X.2022.2077526
  3. Sidiq, M. Fajar, Galuh Renggani Willis, and M. Agus Shidik. "The effect of coffee powder as a carburizing agent and preventing corrosion." In IOP Conference Series: Materials Science and Engineering, vol. 1088, no. 1, p. 012084. IOP Publishing, 2021. https://doi.org/10.1088/1757-899X/1088/1/012084

(3)  Characteristics of hardness and microstructure of extraction forceps for dental and oral care made of stainless-steel; N Kholis, N Nuryanto, A Mustofa; Applied Research and Smart Technology (ARSTech) 1 (2), 56-63 -----> 2 Citations

  1. Hariyanto, Agus, Moustafa Boukraa, and Tawfiq Chekifi. "Transient numerical simulation the friction stir welding process of AA 2017 alloys, contact parameter effects on thermal history and material flow." In AIP Conference Proceedings, vol. 2727, no. 1. AIP Publishing, 2023. https://doi.org/10.1063/5.0153775
  2. Darmawan, Agung Setyo, Pramuko Ilmu Purboputro, Bibit Sugito, Bambang Waluyo Febriantoko, Suprapto Suprapto, and Tjipto Sujitno. "Comparison of commercially pure titanium’s hardness due to plasma nitriding and plasma nitrocarburizing." In AIP Conference Proceedings, vol. 2727, no. 1. AIP Publishing, 2023. https://doi.org/10.1063/5.0141551

(4)  Effects of heat treatment on microstructure and hardness of D2 tools; H Hariningsih, L Lutiyatmi, T Daryanto; Applied Research and Smart Technology (ARSTech) 3 (1), 29-37. -----> 2 Citations

  1. Prabakaran, Vijayasarathi, R. Palani, Pandi Saran, and S. Jenef. "Study of the tribological performance of pre-and post-heat treatment of AISI D2 steel with AlCrN coating under wet conditions." Australian Journal of Multi-Disciplinary Engineering (2023): 1-12. https://doi.org/10.1080/14488388.2023.2193377
  2. Darmawan, Agung Setyo, Agus Dwi Anggono, Agus Yulianto, Bambang Waluyo Febriantoko, Masyrukan Masyrukan, and Abdul Hamid. "Comparison of Microstructure, Yield Strength, Tensile Strength, and Modulus of Elasticity between Gray Cast Iron and Nodular Cast Iron." Key Engineering Materials 935 (2022): 25-32. https://doi.org/10.4028/p-2094w8

(5)  A simplified approach for single carrier visible light communication transceiver using off-the-shelf components; A Ibhaze, P Orukpe, F Edeko; Applied Research and Smart Technology (ARSTech) 1 (2), 64-70. -----> 1 Citation

  1. Ibhaze, Augustus Ehiremen, Agbotiname Lucky Imoize, and Obinna Okoyeigbo. "A brief overview of energy efficiency resources in emerging wireless communication systems." In Telecom, vol. 3, no. 2, pp. 281-300. MDPI, 202; https://doi.org/10.3390/telecom3020016

(6)  Investigation of electrical treeing in perspex material; M Abderrazzaq; Applied Research and Smart Technology (ARSTech) 2 (1), 1-7. -----> 1 Citation

  1. Azhar, Khola, and Salman Amin. "Modeling the effect of uniform and nonuniform dispersion of nanofillers on electrical tree propagation in polyethylene dielectric." Journal of Advanced Dielectrics 12, no. 03 (2022): 2250006; https://doi.org/10.1142/S2010135X22500060

(7)  Potency of natural and synthetic composites for ballistic resistance: A review; MY Yaakob, MP Saion, MA Husin; Applied Research and Smart Technology (ARSTech) 1 (2), 43-55. -----> 2 Citations

  1. Velmurugan, G., L. Natrayan, Yenda Srinivasa Rao, Piyush Gaur, S. Sekar, Rohinikumar Chebolu, Pravin P. Patil, and Prabhu Paramasivam. "Influence of epoxy/nanosilica on mechanical performance of hemp/kevlar fiber reinforced hybrid composite with an ultrasonic frequency." Adsorption Science & Technology 2022 (2022); https://doi.org/10.1155/2022/7233255
  2. Riyadi, Tri Widodo Besar, Waluyo Adi Siswanto, and Xiaomeng Zhu. "Interfacial formation of intermetallic Ni-Al-Ti systems formed by induction heating." Frontiers in Mechanical Engineering 8 (2022): 1005646. https://doi.org/10.3389/fmech.2022.1005646

(8)  Wearable upper limb motion assist robot for eating activity; U Kashtwari, NZ Azlan, I Shahdad; Applied Research and Smart Technology (ARSTech) 1 (1), 1-10. -----> 2 Citations

  1. Azlan, Norsinnira Zainul, and Norhaslinda Kamarudzaman. "Soft pneumatic exoskeleton for wrist and thumb rehabilitation." International Journal of Robotics and Control Systems 1, no. 4 (2021): 440-452; https://doi.org/10.31763/ijrcs.v1i4.447
  2. Azlan, Norsinnira Zainul, and Nurul Syuhadah Lukman. "Assist as Needed Control Strategy for Upper Limb Rehabilitation Robot in Eating Activity." IIUM Engineering Journal 22, no. 1 (2021): 298-322. https://doi.org/10.31436/IIUMEJ.V22I1.1480

(9)  Redesign of water-diesel emulsion fuel mixer; AA Mahadi, B Santoso, U Ubaidillah, BW Lenggana; Applied Research and Smart Technology (ARSTech) 3 (1), 18-28. -----> 1 Citation

  1. Riyadi, Tri WB, Martin S. Hernandez, S. G. Herawan, M. Idris, P. A. Paristiawan, N. R. Putra, R. Silambarasan, and Ibham Veza. "Biodiesel for HCCI engine: Prospects and challenges of sustainability biodiesel for energy transition." Results in Engineering (2023): 100916; https://doi.org/10.1016/j.rineng.2023.100916

(10)  General design criteria for neonatal temperature monitoring sensor using" smart material" conducting polymer development: A review; N Syamimi, S Yahud; Applied Research and Smart Technology (ARSTech) 2 (1), 18-26. -----> 1 Citation

  1. Riyadi, Tri Widodo Besar, Bagus Radiant Utomo, Marwan Effendy, Agung Tri Wijayanta, and Hussain H. Al-Kayiem. "Effect of thermal cycling with various heating rates on the performance of thermoelectric modules." International Journal of Thermal Sciences 178 (2022): 107601; https://doi.org/10.1016/j.ijthermalsci.2022.107601

(11)  Contact stress analysis of a spur gear using Lewis and Hertz theory; A Muhammad, IH Shanono; Applied Research and Smart Technology (ARSTech) 2 (2), 41-46. -----> 1 Citation

  1. Riyadi, Tri Widodo Besar, Waluyo Adi Siswanto, and Xiaomeng Zhu. "Interfacial formation of intermetallic Ni-Al-Ti systems formed by induction heating." Frontiers in Mechanical Engineering 8 (2022): 1005646; https://doi.org/10.3389/fmech.2022.1005646

(12)  Single friction plate clutch design for cars with power of 77 kW and speed of 6000 rpm using finite element method; AS Darmawan, J Syarif, PI Purboputro, A Yulianto, A Hamid, N Noviyanto; Applied Research and Smart Technology (ARSTech) 1 (1), 22-27. -----> 1 Citation

  1. Vardhan, M. Vishnu, TV Sai Narendra, K. Ajay, B. Dhanraj, and C. Anil Kumar. "Design and analysis of single plate clutch by using non-ferrous materials." Materials Today: Proceedings (2023); https://doi.org/10.1016/j.matpr.2023.03.596

(13)  Performance prediction of trailing-edge cooling system of gas turbine blade using detached eddy simulation; A Jamaldi, HK Hassan; Applied Research and Smart Technology (ARSTech) 1 (1), 16-21. -----> 1 Citation

  1. Du, Wei, Lei Luo, Yinghou Jiao, Songtao Wang, Xingchen Li, and Bengt Sunden. "Heat transfer in the trailing region of gas turbines–A state-of-the-art review." Applied Thermal Engineering 199 (2021): 117614; https://doi.org/10.1016/j.applthermaleng.2021.117614

(14)  A remotely-controlled micro airship for wireless coverage. Kafafy, Raed, Mohamed Okasha, Shamma Alblooshi, Hessa Almansoori, Salma Alkaabi, Salma Alshamsi, and Turfa Alkaabi. " Applied Research and Smart Technology (ARSTech)” Vol 3, no. 2 (2022): 72-80 -----> 1 Citation

  1. Kumar, Abhishek, and Om Prakash. "Longitudinal Trim and Stability Analysis of Hybrid Airship with Suspended Payload for Single Body and Two Body Dynamics Using Bifurcation Method." Mathematical Modelling of Engineering Problems 10, no. 2 (2023); https://doi.org/10.18280/mmep.100238